Skip to main content

Mosaic Cutting & Mesh-Backed Sheets

For natural-stone mosaic sheets and glazed ceramic mosaics.

Materials
Ceramic and suitable natural stone, with finishing selected for each face.
Process
Cut repeat-width strips, cross-cut supported chips and polish suitable stone faces before sheet assembly.
See equipment setup
Illustrative workshop layout for Setup 01: HY2-450 Twin-Group Multi-Blade Cutter, HYPGP-600-12 Surface Polisher
2 machines · Est. 14 m² footprint · Actual area may vary

Recommended setup

Setup 01 matches the workshop image above. Compare other setups for different parts or processes.

Setup 01

HY2-450 multi-blade cutter + stone surface polisher

The HY2-450 pre-cuts and finishes parallel strip edges. Trial a supported cross-cut for the smallest chip and polish suitable stone at the stage agreed in the trial.

Workflow

  1. Cut repeat-width strips
  2. Qualify cross-cutting and support for the smallest chip
  3. Polish eligible stone faces at the specified stage
  4. Dry-lay before sheet assembly
  • HY2-450 Twin-Group Multi-Blade Cutter

    Pre-cut and finish parallel cuts to produce repeat-width strips.

    Output
    Repeat-width strips for sorting or a qualified cross-cut.
    Overall size
    2400 × 1600 × 1750 mm
  • HYPGP-600-12 Surface Polisher

    Polish faces of compatible supported natural-stone mosaic material.

    Output
    Stone faces ready for the approved assembly sequence.
    Overall size
    4800 × 2100 × 2000 mm
Compare other setups

Setup 02

HY2 strip cutter + HY1 mosaic cutter

For recurring strip cutting and cross-cutting on separate stations.

Workflow

  1. Cut repeat-width strips
  2. Cross-cut supported pieces
  3. Sort and lay the mesh pattern
  • HY2-450 Twin-Group Multi-Blade Cutter

    Pre-cut and finish parallel cuts to produce repeat-width strips.

    Output
    Repeat-width strips for sorting or a qualified cross-cut.
    Overall size
    2400 × 1600 × 1750 mm
  • HY1 Multi-Blade Mosaic Cutter

    Cross-cut supported strips into repeat pieces.

    Output
    Mosaic particles for sorting.

Compare polished stone faces and glazed ceramic chips, then check joint spacing across adjacent installed sheets. Applications are shown for illustration.

Check the fit for your workshop

Check your drawings against machine limits, then plan how slabs and finished parts will move through the workshop.

Part requirements

Specify strip and chip sizes, sheet pitch and the carrier or backing. Define when stone faces are polished and check that the work stays supported through discharge.

Incoming blank

Specify whole tile or pre-cut strip and the blade spacing in each direction.

Particle support

Trial the smallest piece through discharge and sorting.

Sheet specification

Record the pattern, mesh, joint width and approved backing or adhesive.

Single-machine operations and model details
HY2-450 Twin-Group Multi-Blade CutterMachine details

HY2-450 Twin-Group Multi-Blade Cutter

Functions
Pre-cut and finish parallel cuts to produce repeat-width strips.
Core configuration
Two multi-blade groups pre-cut and finish in the same feed direction. Provide support for a separate perpendicular pass.
HYPGP-600-12 Surface PolisherMachine details

HYPGP-600-12 Surface Polisher

Functions
Polish faces of compatible supported natural-stone mosaic material.
Core configuration
12-head model with 610 mm maximum polishing size and 650 mm belt width. Confirm carrier and piece support.
HY1 Multi-Blade Mosaic CutterMachine details

HY1 Multi-Blade Mosaic Cutter

Functions
Cross-cut supported strips into repeat pieces.
Core configuration
Single multi-blade cutting group. Verify blade spacing and support at the discharge for the smallest specified piece.
Workshop layout and handling

The estimate adds the footprints of the machines in Setup 01. Allow extra room for loading, aisles, servicing and auxiliary equipment. Confirm the installed layout for your site.

Wet and dry separation
Keep wet cutting and polishing separate from bonding and curing.
Sorted batches
Use trays for sizes, colors and orientations to protect the pattern.
Flat assembly bench
Lay out neighboring sheets together and allow room for drying and inspection.
Open workshop floor with slab racks along the back wall.

Technical answers

Before you order

Review machine fit and sample checks, then see what to send for an equipment quote.

Discuss your setup
Do both HY2 cutting groups produce chips in one pass?

The two groups pre-cut and finish parallel cuts in the same feed direction. Qualify a supported perpendicular pass or compare the HY1 cross-cut station for repeat chips.

When should I use the surface polisher?

Use it for supported natural-stone work within the 610 mm polishing width, at the stage agreed in the trial. Check glazed ceramic edge quality on the cutting route.

What should I record from the trial?

Measure edge quality and size on the smallest chip. Lay two neighboring sheets together to check the pattern and joint pitch before bonding. See the finished-part checks.

What do you need for a quote?

Send starting board dimensions, material, chip dimensions, sheet size, pattern pitch and the specified face finish. Include the smallest supported size in the run.

Talk to HoYun

Discuss your equipment needs

Tell us what you make. Include the material, workpiece dimensions, required processes and target output. Add the model if you have a machine in mind.

Explore all machines

Sales enquiries

Connect on WeChat

Scan this code in WeChat or add our sales number. On your phone, save the code to scan from your photos.

HoYun sales WeChat QR code

+86 156 2720 7763

Save QR code

Sales enquiries

Talk to HoYun

Connecting to live chat…

You can also reach our sales team directly.

WhatsApp +86 156 2720 7763Jessie@hoyunmachinery.com